| 第 52 卷第 4 期 |  | Vol. 52 No. 4 | | 2022 年 8 月 | Aug 2022 |
|
所屬欄目：功能材料
載香凝膠珠的制備及其在濾棒中的應用 |
| 王心田，王 月*，劉啟斌，劉 政，馮守愛，胡中軍
（廣西中煙工業有限責任公司，廣西 南寧 530000） |
| 摘 要：為制備聚乙二醇復合咖啡香料的載香凝膠珠，優化其工藝，并驗證載香凝膠珠在煙用濾棒中應用的可行性。采用滴制法進行制備，單因素試驗和正交試驗優選制備工藝，并考察載香凝膠珠的緩釋性能及穩定性，通過濾棒成型機制備添加凝膠珠的煙用濾棒，考察濾棒物理指標。結果表明，載香凝膠珠優化制備工藝是PEG6000作為基質、基質與香料質量配比3∶1、15 ℃二甲基硅油（50 cs）為冷卻液、滴制溫度70 ℃、滴制速度（75±5）粒/min、滴距8 cm，可穩定制備出聚乙二醇基質的咖啡香凝膠珠，載香凝膠珠具有較好的緩釋性能及穩定性。添加載香凝膠珠的濾棒長度均值為120.09 mm，圓周均值為24.28 mm，圓度均值為0.27 mm，壓降均值為3 184 Pa，硬度均值為87.94%，可制備出符合設計要求的載香凝膠珠濾棒，載香凝膠珠具備在煙用濾棒中應用的可行性。 |
| 關鍵詞：聚乙二醇；凝膠珠；制備工藝；煙用濾棒 |
| 中圖分類號：TS426 文獻標識碼：A 文章編號：1009-9212（2022）04-0068-08 |
|
| Preparation of Scented Gel Beads and its Application in Cigarette Filter Rod |
| WANG Xin-tian, WANG Yue*, LIU Qi-bin, LIU Zheng, FENG Shou-ai, HU Zhong-jun
(China Tobacco Guangxi Industrial Co., Ltd., Nanning 530000, China) |
| Abstract：In order to prepare the perfume-loaded gel beads of polyethylene glycol composite with coffee flavor, the optimal process was determined, and then the feasibility of the application of gel beads in cigarette filter rods was verified. The preparation was carried out by dropping method. The preparation process was optimized by single factor experiment and orthogonal experiment, and the slow-release performance and stability of gel beads were investigated. The cigarette filter rods with gel beads were prepared by filter rod molding machine, and the physical indexes of the filter rods were investigated. The results showed that the optimal preparation process of fragrant gel beads was as followings: PEG6000 was used as the matrix, the ratio of matrix to spice was 3:1, the dimethyl silicone oil (50 cs) at 15 °C was used as the coolant, the dropping temperature was 70 ℃, the dropping speed was (75±5) particles/min, and the dropping distance was 8 cm. The coffee fragrant gel beads based on polyethylene glycol could be stably prepared, and the gel beads had good slow-release performance and stability. The average length of filter rod with gel beads was 120.09 mm, the average circumference was 24.28 mm, the average roundness was 0.27 mm, the average pressure drop was 3 184 Pa, and the average hardness was 87.94%. The filter rod with gel beads met the design requirements. The gel beads had the feasibility of application in tobacco filter rods. |
| Key words：polyethylene glycol; gel beads; preparation process; cigarette filter rod |
|
基金項目：廣西中煙工業有限責任公司產學研項目“煙用濾棒功能性顆粒的開發研究”（GXZYCX2020C006）。
|
作者簡介：王心田（1987—），女，廣西南寧人，助理工程師，研究方向：卷煙質量管理（E-mail： 03263@gxzy.cn）。
|
聯 系 人：王 月，工程師，研究方向：卷煙質量管理（E-mail： 00157@gxzy.cn）。
|
收稿日期：2022-05-05
|
|